• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are an excellent option for modern homes. They are long-lasting, durable and easy to maintain. They don't rot or rust like aluminum or timber.

It is essential to clean and oil UPVC doors and windows on a regular basis. This will reduce repair costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause significant damage to your home and even be fatal. It is crucial to take the time to ensure that you're doing all you can to ensure that your windows are in good shape.

Single-pane windows are relatively simple to replace, and they will usually fit into the frames of the past easily. If windows with double glazed window repairs panes are held together by internal beading, it will be harder to remove and replace the panes that were previously in use. In this situation, you will need to find some plastic spacers to aid the new pane in being able to fit correctly into the frame of the window.

Wearing protective eyewear and thick gloves is essential when you are planning to remove the glass yourself. It is also recommended to lay down a dropcloth before you start working on the glass to ensure that any shards fall on the fabric rather than on the floor, where they could be trodden under and cause further damage.

After the glass has been removed from the window, it's best to cover the gap with clear packaging tape or duct tape to stop drafts and water from entering the property until a professional comes out and fix the window. It also acts as a barrier, preventing any intruders from gaining entry to your home. If the gap between the door and the window is large, you might prefer a security screen that also has a window. This will provide the best of both.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash windows. However, over time, they can suffer from a variety of problems including sagging. A window that is sagging can cause problems with light, draughts, and even security. If you find that your uPVC window is beginning to lose its shape, it's important to act quickly to stop the issue from becoming worse.

To fix a window that is sagging you can try to reposition the hinges. First, you'll need to unblock the windows to reach the frame. You can then unscrew both the hinges at the top and bottom with a screwdriver and adjust them clockwise or counter-clockwise. Once you've repositioned the hinges, close the window and verify the fitting. If you are happy with the fit of your window, tighten the screws to secure them in the right position.

If you are unable to reposition the hinges, you might need to replace the seal. Over time, rubber seals lose their elasticity and become dry and cause them to lose tightness. It is essential to replace your seal as soon as you can in order to ensure that your uPVC window repairs near me watertight and draughtproof.

UPVC handles can also loosen up. Often it is due to screws that have come loose over time. However, it could be due to the fact that the handle mechanism has been worn out. It's fairly simple to fix a loose uPVC hand. First, you'll need to close the window and then perform an experiment fit. The joint at the corners of the sash should align with the joint on the casing. If it isn't then you can use a screwdriver to loosen the handle, and then return the mechanism to its original the position it was in.

3. Water Leaks

If you awake to wet floors and mouldy walls every time it rains it is important that you take action. Windows that leak water do can not only cause degrading of the structure of your home but also hinder your efforts to regulate the temperature in your home. Most of the time, uPVC window leaks are caused by a lack or damage to the sealant.

This is a simple fix that can be completed by any DIYer who is competent. Depending on the severity of the issue is, old caulking may need to be removed. It is crucial to remember that when it comes to uPVC window repairs you should not be tempted to apply too much caulk in order to make the area more difficult to clean and could reduce the efficiency of your energy.

It is crucial to make sure that the drainage holes are free of debris and that the sill pan has been angled in a way that allows it to drain away from the window. In more serious cases, you may need to replace the window repair.

Mold spots and rotted sills are other signs of water leakage. The mold thrives in damp environments and is able to quickly spread throughout the house.

It is also important to note that if the leakage originates from the glass in your double glazed windows it may be more likely to be a problem with the glass seal rather than the frame or sagging. It is also possible to be corrected by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or slack and open with a breeze it could be hinges at fault. They can be easily replaced by any competent DIYer and can be done within a few minutes.

Like all mechanical parts hinges will wear out over time. The process of replacing a hinge on a window is essentially a very simple process but it can be easier to do when you have a person to help you hold the frame in place.

Check that the uPVC hinges are closed and open in the proper direction. You can check this by looking for the arrows on each hinge, this indicates the direction in which the window should open.

The issue can be caused either by opening the window incorrectly or a faulty installation at the factory. This can often be resolved by sending us a photograph via our website and we will be happy to give you advice.

Regular lubrication of the hinges is essential. This can be done by applying a light engineering oil to the hinges. We recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window operate and close more smoothly. It also helps prevent corrosion and reduce the risk of sticking. The ideal time to perform this every year. WD40 and other solvent based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts in upvc windows can be caused by a variety of different things. The hinges can also be unbalanced due to wear, creating an opening where the sash and frame meet. If they are beyond repair, it might be required to realign them. The second is the interlock, which is located on the hinge side of the window, may also be misaligned, and again it is possible to just give them a good clean, but in certain cases, it may be necessary to have these replaced.

The next common reason for draughts is window seals. These can become worn down or damaged over time and allow air to escape through the gaps. Replacement of these with high-quality weatherstripping will help to keep draughts at bay. Another alternative is to replace the window with low-emissivity glass. which will help regulate indoor temperatures, and also reduce draughts.

The last way to reduce draughts effectively is by using a draught-excluder. These are typically fabric tubes filled with a filler that can be hung over your window sill. These will keep your home warm by blocking cold air.

With a little maintenance and repair windows made of upvc will provide an excellent level of insulation and security for your home. It is crucial to recognise that all windows have a lifespan and they may reach a point where it is more cost-effective to replace them rather than fix them. If you have any problems with your Upvc window, it's best to consult an expert as soon as you can.