• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

boarding up doors Up a Doorway

Boarding up a doorway keeps rain, snow and hail from further damaging the property. It also helps keep vandals, squatters and scavengers away.

Doors are more secure than windows, however they can still be broken or kicked into. These doors should be paired with composite frame that won't warp over time.

Find the Doorway

A doorway is a hole in a wall, through which you can enter or exit the building, room, or the passageway. A doorway could be an access point that allows you to go to a different location, such as another room in the house, or an entirely different area of the country.

You'll need to measure the doorway. Begin by measuring the width of one side of the frame to the opposite side using the tape measure. It is important to remove any trim or brickmould before taking this measurement. This will ensure that you only measure the frame, not the actual door or window. Use the largest number of these measurements to determine the size of the doorway.

If you're looking to replace the door, take a measure of the door's opening. It is possible to do this without removing the door by prying the old one away from the jamb with the wide tool. This will reveal the rough framing which will be used to hang the new door. Measure the height of the opening in three places and use the smallest of the numbers as the height of the new door.

You can also measure the width of the doorway by running a tape measure across the frame at three different places: left, center and right. Take the measurement with the highest value to determine the width. This is the most effective method to ensure your plywood will cover all the area, and also allow you to put in the door or window you want to replace.

Measure the Frame

Boarding up windows doors, windows, and other openings which let in the elements can offer a substantial amount of security for your home. The first step is to carefully inspect each window to determine its size and shape, and then take measurements of the width of the frame. Note down each measurement, so that you can cut the plywood boards to the dimensions of the frame.

Wear protective gear prior to beginning to shield yourself from broken glass and other hazards. Also, it is recommended to work with a friend because handling large sheets of plywood is much easier with an extra set of hands.

Use wide masking tape to secure the cracks, and then remove any panes which aren't taped. Be safe and protect the remaining panes with heavy plastic trash bags. Seal the trash bags from the inside to increase their strength.

If the frame is still good it is possible to save time by putting a new stud through the gap in the middle of the window. This will give the board-up more strength, without the additional effort of removing and installing the framing itself.

Purchase a few sheets of plywood, and tools like a hammer, drill and saw (if cutting is required). Based on the frame's dimensions and marking each board with its corresponding window number. Then, using the pilot holes you made earlier, connect the plywood to the frame.

Find the Jambs

The jambs are three pieces wood that the door is directly mounted. They're essential in keeping a door closed correctly and should be tight and level. If the jambs you have aren't, you'll need to adjust them.

Begin with the hinge side jambs with a raised portion towards the center, which is referred to as a doorstop. The doorstop rests against the slab of the door and prevents it from hitting the frame when it closes. Screw a strip of plywood to the bottom of each stud such that it raises the floor within the opening in about 1/2 inch (photo). This will help prevent the door from scraping against the tile or carpet when it is shut and opened.

To get an accurate measurement of the hinge's side jamb, remove any trim or molding installed around it. This will reveal the rough opening, allowing you to accurately measure it.

Note the locations of the hinge holes both on the outside and inside of the hinge jamb. Utilizing a combination-square, determine the depth of the hinge mortise and adjust the square to match the marks on the jamb of the hinge. This will ensure that the hinge is centered within the frame and aligned with the door. Repeat the process for the latch jamb. Utilize a nail gun as well as finishing screws of 2 1/2 inches to secure the strike side.

Find the Header

A header is a large dimensional lumber board that is fixed to the wall framing. It carries loads above the door and window openings to the studs below. When properly frame the King and Jack studs are nailed on each end of the header. They also butt up against the header on both ends to form a strong column that transfers the weight of the opening to the floor and foundation.

In conventionally framed houses you can make use of a set of tables in the code to calculate the size of a header for a given span. A typical header is a double 2x12 and the code provides tables for three widths of a building and you can use interpolation to get the next wider size to get the appropriate header size.

But there are other more efficient alternatives to the standard 2x12 header that can save lumber, cut down on thermal bridging and free up space to be used for insulation. Builder Mike Guertin takes a look at these options and when they're suitable:

He also talks about rim-board headers, which can connect an opening in the wall without using a header; this eliminates a step in the framing process and often results in an even stronger frame. He also explains box headers, which are more difficult to construct, but offer greater spans than single-ply. He also covers the fastening schedule for these different headers. This calls for 8d common nails spaced every three inches.

Cut the boards

Before boarding up commercial property up a door [linked internet page], it is important to clean the area thoroughly. To make enough room for work and to prevent damage to your belongings, you must take out all furniture and decorations. Detach the doorknobs and locks and store them in a safe location to be reinstalled later. To ensure better adhesion, wash the door and frame and clean all surfaces to remove dust and dirt. If needed you need to sand rough areas to ensure that the boards fit properly and offer effective protection.

Once the doorway is cleared, you can begin cutting the plywood. A circular saw can make straight cuts through wood and cut easily through it, whereas a Jigsaw is ideal for curved areas. Wearing protective equipment, such as safety goggles as well as a dust mask, is essential during this process.

After cutting the board to size, it is important to verify its alignment with the frame and jambs. It is also a good idea to add a few vertical pieces of lumber to the bottom of the board to provide reinforcement. After the board has been properly aligned and secured, it is now ready to be put in the desired position.

A doorway that is boarded up can help protect the property or home from damage and unauthorized entry during a storm, disaster or other occurrence. It can also be used to protect vacant properties or prevent theft and break-ins until the property has been used. A thorough assessment of the situation and the reason of the 24 hour boarding up service near me up will help to guide the material selection and the method of installation to achieve the best results.

Install the Boards

The boards should be screwed down using screws that are heavy-duty instead of nails. The strength of these fasteners will distribute pressure and resist prying, enhancing the effectiveness of your board. The sealing of the edges with caulk or weatherstripping can stop water and wind from leaking through the gaps. It's also an excellent idea to leave a space for ventilation in order to avoid stale air and moisture buildup.

Wearing gloves and goggles is a must when using a power tool. Mark your cuts using the aid of a straightedge and pencil because mistakes are more difficult to rectify after cutting. You'll need to be as precise as you can when cutting the boards so they're perfectly fitted against the door frame and casing. The jambs and the head must be cut to make sure they're in line with the wall.

It's best to do this prior to the storm's arrival so that you will have plenty of time to board up other areas that are at risk. A little planning will save you a lot of time and help you prepare your home or business for the possibility of a catastrophe. Your property can be secured from criminal activity, wind and flying debris with the right preparation. You'll also have peace of mind knowing your property is secure.