• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace a Kia Sportage Replacement Key

For a variety of Kia models the key comes with a keyless entry system built-in. The key is usually akin to the remote control and can be changed with a new one from a Kia dealer or locksmith.

Key fobs are prone to malfunction due to a variety of reasons, including batteries that are dead worn buttons signal interference, water damage, and a defective receiver module. Here are some suggestions on how to get your Kia Sportage replacement key back to working.

How do you replace the remote key or smartkey?

The battery inside your 2011 kia sportage key fob's smart key will eventually need be replaced, regardless of whether it is a remote key, a push-to-start key or a standard metal key that doesn't contain transponder. This is especially true if the car displays a message that the smart key or remote is not powered by the battery.

Luckily, this is an easy process. In order to replace the battery on the key fob remove the mechanical key from the slit at the back of the key fob. Then pry open the cover. Inside the key fob will be tiny screws that hold the battery in place. Remove the old battery by removing the screw using a small screwdriver. Install the new battery and then close the cut on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock exactly as you expect, then you're all set! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers become chilly or when you need to complete errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a special programming machine that only the dealer or automotive locksmith has access to. Other keys (non transponder metal keys) do not require programming. If your key has to be programmed, you will need to be aware of the key code number that is stamped on the tag that identifies the key and keep it in a safe location.

How do I replace a battery

If the Kia key programming near me fob is unable to respond to pressing the lock or unlock button, it is most likely that the battery is low. A low battery could cause other issues like the check engine light turning on or the engine not cranking. Fortunately, replacing the battery on the key fob is a simple DIY task that requires only some basic tools.

Be sure to turn off your vehicle and shut the doors before you begin. Find the small, metal or plastic piece at the bottom of your key fob, and play with it until a metallic key is released. The key can be placed inside the driver door handle to unlock your car.

To replace the key fob battery, take off the cover on the rear and use a plastic pry bar tool to remove the latch that holds the black negative battery cable. Take the old battery out, and then position the new battery to ensure its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into position to avoid damaging or breaking the metal contacts.

After you have installed the new battery, turn the key fob on and off in the ignition until the door locks up. You can then test the Kia's Key fob to ensure it's working properly.

How can you replace the smart key

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The smart key comes with an embedded mechanical key blade while the standard keyfob does not. Both kinds of key fobs contain batteries that eventually will need to be replaced. This is a straightforward process that takes just two minutes.

Before you get started it is important to ensure that you are on a level surface with sufficient lighting and that your Kia is off. Be aware that the fob has tiny pieces that could be thrown off should you not be careful.

The first step is to find the small release button on the lower backside of your fob. It could be a circular silver button or a rectangular slot. When you press it mechanical key blade, it will pop out and you can then open the key fob.

After the key fob has been open, remove the battery that was in it. The new battery should be a CR-2032, and can be purchased online or at a local auto parts store. When you're done, the key fob will allow you to lock or unlock and start your vehicle, even if it isn't running.

How do you replace the mechanical key?

The 2014 Kia optima key Fob key fob is an amazing convenience that allows us to lock and unlock our car at the click of the button. However, like all devices, it can have problems occasionally. There are ways to troubleshoot these issues and ensure that our key fobs are in good working order for the long run.

A low or dead battery is among the most frequent problems. The battery could cause the device to stop working or work intermittently. If this is the problem it is time to replace the battery an entirely new battery.

If this doesn't solve the issue, try using a flathead screwdriver standard to push the fob's plastic casing open. Be cautious not to damage any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a new one.

Once the new battery is in, close and open the doors using the mechanical key (every kia key fob programming fob has an emergency mechanical key that will fit into the slot). Test the key fob to check that it's functioning correctly. Contact a dealer or locksmith to resolve the problem if the fob is still not working. To avoid a lockout in the future make sure you get an emergency key that can work in all of the door and trunk cylinders.