• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your cat go inside and out as they please without you having to let them in or out. They also help keep your cat from having to go to the bathroom in the house.

Installing a cat flap into a upvc door panel is much easier than in glass doors, however it requires some knowledge and the appropriate tools.

Measure the Door

Fitting a cat door in a front door can be difficult, but provided that the cat flap is of the appropriate one and you follow the instructions it shouldn't be too difficult. We will help you mark the shape and use an jigsaw to cut out the door's area. Then, we'll finish the job by attaching the cat flap. This will ensure the flap stays in position and shields the doors from damage caused by wind and rain.

The first thing you need to do is determine the width of your pet to get an accurate measurement of what size of cat flap you will require. This will ensure that the flap is large enough to let your pet leave and enter the home without having to open or close the door each time, but also small enough to keep them from going too far either way.

If your kit comes with an illustration of the location to drill then you can stick it on the door, and then draw a pencil around it. If your door has a sill or moulding at the bottom, be sure you leave plenty of space between your cat and the moulding or sill.

Put on your eye protection and dust mask, and using a jigsaw begin cutting according to the lines you penciled in, but don't push the blade too hard, as this can cause it to cut faster than you want it to. Use a set square to ensure you are cutting the material in a proper manner and that the cut is a rectangle. When you are satisfied with the result, you are able to take the door material off.

Draw a Line

The cat flap allows you to let your pet in and out without worrying about unwanted visitors or unwelcome gifts. It also reduces drafts and helps keep the temperature in your home steady. However, putting an animal flap on your door can seem like an overwhelming task for those who've never done it before, leading many to hire an expert joiner or carpenter to do the job. This is a viable option, however you can do it yourself if the tools are appropriate and the directions are adhered to.

While this is far simpler to accomplish with a wooden door, it is still possible to do this in uPVC doors, but you need to be very careful to avoid damaging the doors, as this can invalidate the warranty. The first step is to measure the door and ensure that it is able to accommodate the new cat flap. If you have a standard uPVC panel it's easy. However, if your door is composite or a different type of door, you may have to be more cautious.

The next step is to measure the height of your cat's belly. This is the height from the floor to the underside of the cat's stomach and you'll need to find a place on the door where this measurement is within the range that your pet can comfortably go through wall cat flap. Once you've got the information you'll need to mark the area with a spirit-level and a pencil so that you are certain that the hole will fit your cat flap installation cost.

Once you've marked the area, it's now time to cut the hole. It is important to be patient and use a jigsaw in order to ensure that the cuts are smooth and clean not uneven and rough. This could cause damage to your door. You should also remember to wear safety glasses and a dust protection mask whenever using the jigsaw, as inhaling the sawdust could be harmful to your health. After you've finished the cutting process, you will have to smooth the edges of the hole using sandpaper, so that the cat flap can be fitted easily into place.

Cut a hole

Installing a cat flap into an existing door panel or double glazing sealed unit is quite difficult. You might be tempted to tackle the job yourself, but unless you have plenty of experience in DIY it is probably best to get a professional in to do the task for you. A mistake in the process may not only be unsightly but also an issue for security as well as allowing cold air to get in when the cat is outside, and hot air to escape when inside.

The first thing to do is draw the position of the hole in the door using pencil and a spirit level. This will ensure that it is positioned and that it runs in a straight line with the other parts of the door. Make sure to have sandpaper to smooth any rough edges.

Wear the safety equipment you require when working with an electric tool. If you are worried about the sound produced by a jigsaw you can buy one that is cordless, which is much quieter and easier to use.

It is important that you only cut away the material needed to make the cat flap. It is essential to leave a little extra material to cover the wall of the cat flap. However cutting away too much could cause issues or even damage the door frame.

A upvc door may contain a metal frame or a panel inside that will interfere with the microchip cat flap, and if this is the case, you'll need to cut an oversize hole so that the metal does not touch the the cat flap. If this is done it is important to fill in the oversize gap and render it watertight.

If you are Fitting cat flap in upvc door panel (yanyiku.cn) an animal flap to a upvc door or double glazed windows with a metal frame, you will need to speak to a specialist who can provide you with a new glass pane window with cat flap the hole for the cat flap inside. It is much less expensive to have this done than trying to fix a cat flap into an existing glass pane that has not been manufactured specifically for this purpose.

Install the Flap

Cat flaps give your pet the freedom to go and come whenever they like, allowing them to relax in the home whenever they like. However, if you own an uPVC door, it may be difficult to put in a cat flap, especially in the absence of a glass pane that can be cut for one. If you're able to purchase and install a half-glazed replacement uPVC panel, it's possible to install an animal flap onto the doors. It's not just a matter of drilling holes in the door. It is also necessary to take a few steps to ensure that the door is safe.

A composite, uPVC or GRP door panel is generally composed of a thin plastic skin that is attached to an insulating polystyrene core. The material is fairly fragile and care should be taken when cutting into it to avoid causing damage. This kind of door has a template you can use to make the hole.

After you have carved out the opening in your front door, it's time to install the cat flap. You can choose from a variety of options, from simple push-button flaps to ones that are microchip-activated and allow only your pet to enter. But, regardless of the kind of cat flap you select, it's important to make sure that your cat is able to use the flap without getting stuck outside in the rain.

A circular fitting is more effective than a square because circles can be cut more securely into glass. This is because square holes can leave the glass vulnerable to cracking if drills are used on it. It's also a safer option to use as you're not at risk of having to drill into toughened glass that could shatter and hurt your pet or family members. This is especially important if there are children or elderly people at home who could be injured by glass shards.